Power Handi Vac 100

     Power Handi Vac 200

     JetMAX Junior

     JetMAX

     JetMAX Turbo


Recommended for pools up to 120' / 37m long

JETMAX TURBO UNIQUE FEATURES INCLUDE:

  • Virtually FREE of consumable “wear and tear” parts.
  • 120’ floating cable to accommodate the largest pools.
  • 2 Year Warranty on plastics, electronics and motors.
  • At 18 pounds it is easy to handle, operate and remove from the pool.
  • Cleans all commercial pools up to 120 feet long; in half the time of any other cleaner.
  • Unique scanning pattern guides the cleaner to fully vacuum most pool floors in about 1 hour.
  • Complete set of Filter Bags (1 Fine Filter / 1 Mesh Filter) to capture all types of debris.
  • Perfect for the slopes, curls, and curves of Grecian, Kidney-shape, or gradient-walled pools.
  • JetDrive Propulsion uses the water pressure from the Pump to move the unit. No Drive Motor needed!
  • High-Volume Pump Motor increases cleaner suction, filtration, and Jet Drive propulsion speed.
  • Obstacle Sensors to detect walls and objects in the pool. Magnetic sensors detect stopped motion.
  • Non-scuff rubber wheels guide the momentum of the JetDrive Propulsion. No Belts or Tracks needed!
  • Hydroscrub System power-washes debris from the floor with pressurized water. No Brushes needed!
  • Pump has Thermostat Box to regulate temperature, prolong motor life and reduce service costs.
  • Customizable Directional Guidance adjustments enable efficient systematic width-to-width cleaning patterned movements.
  • StayCool™ Power Supply with internal digital 1-7 hour adjustable automatic shut-off Timer.
  • External timer system operable (e.g. can connect to house type timer or via relay to pool auto-control system)
  • NEW! Manual Guidance Attachment (MGA) provides manual spot cleaning operation via connection of standard extension pole.

 

Technical Specifications Sheet
Recommended Pool Length:
≤ 120' / 37m
Maximum Pool Volume:
700,000 Gals. / 2,650,000 Liters
Maximum Pool Size:
12,000 Ft2 / 1,114.8 m2
RPM Under No Load After The Gear Box:
N/A
Cleaner Speed
(distance per second)
1.00’ / .31m
Filtration / Circulation (volume per minute):
110 GPM / 416 Liters
Filtration Particulate Removal (nominal)
Down to 2µ
Filter Maximum Volume Debris Holding Capacity:
45 Quarts / 42.59 Liters
Cable Length:
120' / 36m
Floor / Wall Cleaning:
Yes*
Remote Control:
No
Cleaning Cycle Auto-Start Delay:
No
Manual Guidance Attachment (MGA) Feature:
Yes
Tangible Brushing:
N/A
HydroScrubbing / DeepClean™ Power Washing:
Yes / 2
Pump Motor(s):
1
Drive Motor(s):
No
Drive Feature:
Hydraulic Jet Drive Propulsion
Guidance Pattern:
Adjustable Directional Wedge (systematic scanning)
Air Sensor / Zero-Depth Beach Entry:
No
Obstacle Avoidance (VGB, etc.):
Yes
Clean Time (approximate)
<2 Hours
Automatic Shut-Off / External Timer Operability:
1-7 Hour Adjustable Timer / External Timer Operable
Debris Intake Port Size:
.815 x 5.89” (4.80 sq. in.) / 2.07 x 14.95 cm (30.95 sq. cm)
Cleaning Path Width:
20.5” / 52.07 cm
Operating Voltage @ 60 cycles:
115v / 28v
Energy Consumption in Kilowatts:
.18KW
Warranty:
2 Years
Cleaner Weight:
17.5 lbs. / 7.9 KG
Cleaner Dimensions (L x W x H):
20 x 21 x 11 inch / 50.8 x 53.34 x 27.94 cm
Packaging Dimensions (L x W x H):
28 x 19 x 15” / 71.1 x 48.3 x 38.1 cm
Shipping Weight:
43 lbs. / 19.5 KG

Product Videos

This div is replaced by the javascript using swfobject

This div is replaced by the javascript using swfobject

Manual Guidance Attachment

  • Position the Back Plate over the center of the JetMAX label on the back of the unit. (The back is the side with the stationary, non-sliding axle.)

  • The Body should have four holes pre-drilled behind the JetMAX label. Use the Back Plate to easily identify, push through and open the holes.

  • If the holes are not predrilled behind the label, use the holes in the Back Plate as a template to drill through the plastic Body.

  • Place the Front Plate over the holes and insert the four screws provided.

  • Remove the Bottom Lid Assembly from the unit, look within and locate the ends of the four screws inserted through the Front Plate.

  • Align the Back Plate over the four screws, place it flush against the Body and install the four lock nuts onto the screws.

  • While grasping the lock nuts inside of the cleaner, tighten all four screws using a Phillips-head screwdriver.

  • Line up the holes of the Front Plate’s arms with the holes of the Handle Bracket and install the Clevis Pin.

  • Slide the Lock Ring through the small hole in end of the Clevis Pin. The MGA installation is now complete.

Additional Photos

 

Printable PDF Brochure

Get the information you want now. Download the product information brochures via PDF. This requires
Adobe Acrobat Reader® software. If you wish to have a brochure mailed to you click here

Click here to download